300MW锅炉低NOx燃烧系统改造效果分析

针对日益严重的环境污染、锅炉热效率低等问题，阐述了燃煤锅炉炉内空间分级燃烧技术、煤粉浓淡高效分离技术改造项目和特点，提出了对燃烧器系统、一次风管道、二次风系统和空预器系统等系统进行具体的低氮改造措施。分析了300 MW燃煤锅炉低氮改造后的热经济性和安全性。经试验验证，1号锅炉低氮改造后，锅炉NOx 排放量大幅减少，排放浓度降到了280 mg／m3。     

大肠杆菌吸附-化学还原法用废含金催化剂制备金纳米线

采用大肠杆菌吸附-化学还原法,以大肠杆菌(ECCs)为模板、十六烷基三甲基溴化铵为保护剂、抗坏血酸为还原剂,由废含金催化剂制备金纳米线(AuNWs)。采用XRD,SEM,TEM等技术对AuNWs进行表征。研究了AuNWs对罗丹明6G(R6G)和4-巯基苯甲酸(4-MBA)的拉曼散射信号的增强效果。实验结果表明:在制备过程中加入微生物ECCs,可使金回收率提高约20百分点;当溶液pH小于4时,反应2 h后,有大量呈线状的AuNWs聚集沉降,金回收率可达99%1以上。表征结果显示,AuNWs呈多晶结构,晶格间距为0.23 nm。表面增强拉曼散射分析表明,AuNWs对R6G和4-MBA具有良好的拉曼光谱增强性能。     

Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

The accounting method and application of CO2 emissions responsibility by the electricity sector at the provincial level in China

When accounting the CO₂ emissions responsibility of the electricity sector at the provincial level in China,it is of great significance to consider the scope of both producers’ and the consumers’ responsibility,since this will promote fairness in defining emission responsibility and enhance cooperation in emission reduction among provinces.This paper proposes a new method for calculating carbon emissions from the power sector at the provincial level based on the shared responsibility principle and taking into account interregional power exchange.This method can not only be used to account the emission responsibility shared by both the electricity production side and the consumption side,but it is also applicable for calculating the corresponding emission responsibility undertaken by those provinces with net electricity outflow and inflow.This method has been used to account for the carbon emissions responsibilities of the power sector at the provincial level in China since 2011.The empirical results indicate that compared with the production-based accounting method,the carbon emissions of major power-generation provinces in China calculated by the shared responsibility accounting method are reduced by at least 10%,but those of other power-consumption provinces are increased by 20% or more.Secondly,based on the principle of shared responsibility accounting,Inner Mongolia has the highest carbon emissions from the power sector while Hainan has the lowest.Thirdly,four provinces,including Inner Mongolia,Shanxi,Hubei and Anhui,have the highest carbon emissions from net electricity outflow- 14 million t in 2011,accounting for 74.42% of total carbon emissions from net electricity outflow in China.Six provinces,including Hebei,Beijing,Guangdong,Liaoning,Shandong,and Jiangsu,have the highest carbon emissions from net electricity inflow- 11 million t in 2011,accounting for 71.44% of total carbon emissions from net electricity inflow in China.Lastly,this paper has estimated the emission factors of electricity consumption at the provincial level,which can avoid repeated calculations when accounting the emission responsibility of power consumption terminals（e.g.construction,automobile manufacturing and other industries）.In addition,these emission factors can also be used to account the emission responsibilities of provincial power grids.     

The State of the Mammal Community of Boreal Forest Ecosystems in the Vicinity of a Nickel-Smelting Plant

The effect of industrial air pollution on natural small mammal populations has been studied in the northern taiga subzone of the boreal forest zone. The results of long-term monitoring have been used to demonstrate the possibility of predicting changes in the main population and community characteristics of the animal species studied as dependent on the degree of anthropogenic impact.     

Source characterization of ambient fine particles at multiple sites in the Seattle area

To identify major PM_2.5 (particulate matter ≤2.5 μm in aerodynamic diameter) sources with a particular emphasis on the ship engine emissions from a major port, integrated 24 h PM_2.5 speciation data collected between 2000 and 2005 at five United State Environmental Protection Agency's Speciation Trends Network monitoring sites in Seattle, WA were analyzed. Seven to ten PM_2.5 sources were identified through the application of positive matrix factorization (PMF). Secondary particles (12–26% for secondary nitrate; 17–20% for secondary sulfate) and gasoline vehicle emissions (13–31%) made the largest contributions to the PM_2.5 mass concentrations at all of the monitoring sites except for the residential Lake Forest site, where wood smoke contributed the most PM_2.5 mass (31%). Other identified sources include diesel vehicle emissions, airborne soil, residual oil combustion, sea salt, aged sea salt, metal processing, and cement kiln. Residual oil combustion sources identified at multiple monitoring sites point clearly to the Port of Seattle suggesting ship emissions as the source of oil combustion particles. In addition, the relationship between sulfate concentrations and the oil combustion emissions indicated contributions of ship emissions to the local sulfate concentrations. The analysis of spatial variability of PM_2.5 sources shows that the spatial distributions of several PM_2.5 sources were heterogeneous within a given air shed.     

潮土细菌及真菌群落对化肥减量配施有机肥和秸秆的响应

为了研究化肥减量配施有机肥和秸秆对华北麦玉轮作田潮土细菌和真菌群落的影响,在天津市宁河区试验基地开展田间定位施肥试验,采用Illumina高通量测序技术比较了5种施肥模式（单施化肥处理,F;化肥减施处理,FR;化肥减量与秸秆配施处理,FRS;化肥减量与有机肥配施处理,FRO;化肥减量与有机肥和秸秆配施处理,FROS）下土壤细菌及真菌群落的组成、多样性和结构差异,并结合土壤理化性质分析,探究不同施肥处理下驱动细菌和真菌群落变化的关键土壤环境因子.结果表明,FRO处理显著提高了土壤SOM含量.FROS处理的TP含量显著高于FRS处理,增加了13.33%.FRO和FROS处理AP含量较其它处理显著增加,NH₄⁺-N含量显著高于化肥处理（F和FR）.各施肥处理土壤中优势细菌门类均为变形菌门（Proteobacteria）、放线菌门（Actinobacteria）、绿弯菌门（Chloroflexi）和酸杆菌门（Acidobacteria）,优势真菌门类均为子囊菌门（Ascomycota）.在化肥减量配施有机肥（FRO）的基础上添加秸秆（FROS）显著降低了放线菌门（Actinobacteria）的相对丰度.FRS和FROS处理均显著降低了芽单胞菌门（Gemmatimonadetes）的相对丰度.FROS处理显著提高了浮霉菌门（Planctomycetes）和疣微菌门（Verrucomicrobia）的相对丰度.对于真菌群落而言,有机肥（FRO和FROS）的施入显著提高了子囊菌门（Ascomycota）的相对丰度.与FR处理相比,FROS处理显著降低了被孢菌门（Mortierellomycota）和油壶菌门（Olpidiomycota）的相对丰度,且FRS处理同样显著降低了油壶菌门（Olpidiomycota）的相对丰度.FROS处理的细菌群落Shannon多样性指数显著高于F和FR处理,分别增加了1.26%和1.25%,Chao1指数较F处理显著增加了4.51%,细菌Shannon多样性指数与AP和NH₄⁺-N含量显著正相关（P<0.05）.与FR处理相比,FRS、FRO和FROS处理显著降低了真菌群落Shannon多样性指数,分别达到29.85%、24.94%和25.73%,真菌Shannon多样性指数与AP含量显著负相关（P<0.05）.细菌群落结构在FROS处理下显著区别于F、FR和FRO处理,土壤SM、TP、pH和AP是导致细菌群落结构变化的主要驱动因子;真菌群落结构在FRO和FROS处理下显著区别于F和FR处理,真菌群落结构变化主要受土壤TN、AP和TP的驱动.综上所述,添加有机肥和秸秆改变了土壤理化性质,进而改变了土壤细菌和真菌群落组成,土壤真菌对有机物料的敏感程度高于细菌,细菌和真菌群落结构均受到土壤P的调控,在潮土农业耕作中应引起充分重视.     

中国集成电路制造行业VOCs排放特征及控制对策

中国电子信息产业发展迅速,集成电路等电子器件产量不断增加.在集成电路制造的过程中,大量有机溶剂的使用导致VOCs的产生和排放,从而对大气环境造成影响.为掌握集成电路制造行业VOCs的排放特征,系统分析了其工艺流程和产排污环节,分析了行业废气收集和治理现状,通过对典型企业VOCs的排放监测,获得VOCs排放水平;采用排放因子法核算行业VOCs历史排放量,并基于行业排放特征及减排潜力分析,提出了相应的污染防治对策.结果表明：在集成电路制造中,VOCs排放环节主要集中在光刻、清洗、去胶等过程,1 m²集成电路产量约使用87 g有机溶剂,VOCs产生量较大;通过采取高效的VOCs治理技术,集成电路制造行业有组织排放水平较低,平均浓度为2.1 mg·m^-3,但厂界无组织排放浓度相对较高,平均浓度为0.78 mg·m^-3,接近国家标准的排放限值.根据排放量核算结果,2011—2016年中国集成电路制造行业VOCs排放量呈逐年上升的趋势,主要受产量增加而相应污染控制技术水平提升有限的影响,无组织排放量比重大,占排放总量的38.1%~45.1%.     

基于遥感尾气监测的柴油车气态污染物排放因子计算方法研究

采用遥感尾气测试系统实测了柴油车在实际道路工况下的CO、HC和NO排放特征,修正了排放因子的计算方法,并与车载排放测试系统（PEMS）实测结果进行了验证,获得了实测车辆的CO、HC和NO排放因子.测试结果显示,在各种遥感监测的工况下柴油车尾气中均含有较高浓度的氧气,未考虑氧气影响的燃烧方程反演获得的各污染物体积浓度计算值与PEMS实测值的偏差较大,且氧气浓度越大,偏差越大.经过氧气修正的燃烧方程反演计算的尾气浓度与PEMS实测值吻合度大幅提升,适用于实际工况下遥感检测车辆尾气的反演计算.修正算法得到CO、HC和NO的排放因子离散性较小,精确度较高,可以为量化柴油车尾气排放贡献提供科学依据.     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.